If you want to know how to replace the iPhone 4s screen, this article will walk you through the process. First, you will need to disassemble your iPhone 4S. Next, you will want to disconnect the battery connector and the copper contact from the screen.
Lastly, you will need to remove the adhesive film. Now, you can replace the screen by following these steps. To do this, you will need to purchase a new display assembly.
Disassemble iPhone 4S
To replace the screen on an iPhone 4S, you need to disassemble it. There are a few steps you can take to disassemble your phone. First, remove the logic board. Then, remove the two screws holding the rear-facing camera and loud speaker assembly in place. These screws should be removed using a Phillips screwdriver. After removing the screws, guide the touch cable through the midplane.
If the screen is not damaged, you can disassemble the entire phone to replace the screen. You should turn off your phone first for safety purposes. Next, remove the back plate and battery. You can now remove the logic board shields, rear-facing camera, dock connector, and SIM card. Once you have removed these parts, you can replace the screen. Make sure you follow the instructions carefully. Disassembling your phone isn’t as difficult as you think.
Then, carefully remove the four screws holding the LCD panel and speaker mesh. You’ll also need to remove the standby/proximity sensor, which is soldered onto the logic board. Make sure to carefully disconnect it from the logic board. Connect the LCD and touchscreen back into their respective compartments. You can also clean the iPhone 4S with a damp cloth. Once you’re finished, assemble the phone and test its operation by dialing numbers or using the keyboard. Be sure to check all parts for dead pixels. Congratulations! You just earned yourself a ninja DIY award. And you’re on your way to fixing your iPhone!
Before removing the screen, you’ll need to remove the battery and the SIM card. These parts are held in place by two screws on the bottom. The battery connector is also held in place by a small screw. The battery connector is connected to the SIM card tray with two other screws. Make sure the battery is properly connected to the phone. The SIM card tray is connected to the SIM card slot. Screw the battery in place.
Remove Battery Connector
To replace the screen on your iPhone, first remove the battery connector. This part is attached to the battery through two small Phillips screws. Make sure to note the screw’s length, as they are not the same length. Next, remove the battery, ensuring that you don’t damage the logic board. Next, unscrew the bottom plastic tab from the new battery. Make sure to place it aside before proceeding.
You should find the battery connector panel on the bottom left side of your iPhone. The battery is attached to the logic board with two screws. Use a plastic opening tool to pry up the battery connector. Make sure to pry up the battery vertically, as pushing it sideways can damage the connector. Then, you can unscrew the screws holding down the battery. Be careful not to bend or break the battery connector, as the battery is a very tiny piece.
Next, you will need a plastic spatula or a small screwdriver. Remove the shield covering the dock connector cable with a #00 Phillips screwdriver or a spudger tool. The cable is held in place by adhesive. Gently pry up the round connection that connects the cellular antenna. The connection should pop up with little force. You’re now ready to remove the old screen and install the new one.
Now that you know how to remove the battery connector, it’s time to disassemble your iPhone and replace the screen. You’ll need a screwdriver and prying tool, but you don’t need to be a mechanic to do the job. If you’re not confident in your skills, hire someone who can help you. There are a lot of third-party repair blogs and websites that will walk you through the process step-by-step.
While replacing the iPhone 4s screen isn’t as difficult as it is on newer iPhone models, you shouldn’t attempt it without proper tools and training. If you don’t have experience with technology repair, you could damage your iPhone or even void its warranty. However, it’s not difficult to replace the screen on your iPhone 4s if you’re willing to take the time to learn how to do it yourself. First, pull the rear panel of your phone away from the top edge of the phone. Gently pull out the battery while taking care to avoid breaking any small clips.
Remove Adhesive Film from iPhone 4s Screen
To replace the iPhone 4s screen, you must remove the protective film first. The adhesive film is very thin and is usually applied directly to the surface of the screen. In some cases, the film even has a serial number imprinted on it. Once you remove the film, you can easily install a new screen. This guide will help you with the process of removing the protective film. It is important to read the instructions carefully and take note of any special precautions.
Then, take a microfiber cloth and dust removal tabs and prepare the adhesive film. You need to spread it evenly over the screen. Make sure to align the display and press it to the glass. Once the film is positioned correctly, you can peel it off. To ensure that the new film is secure, you should place your iPhone in a wind and dust-free environment. The adhesive film will heal within 24 hours, so it’s a good idea to do this in a well-ventilated area.
The protective film is also very thin and doesn’t need to be removed completely. There are two films included in the package, and they will protect the display of your iPhone. The clear one will protect the screen and reduce scratches. The film will also help protect the phone’s rear panel from shocks. After you remove the film, you can easily clean the phone’s screen and restore it to perfect condition. If you don’t know how to remove the protective film, try using a credit card or a cloth to remove the air bubbles.
Next, remove the speaker. You can also remove the screws holding the speaker. You can use a heatgun to loosen the adhesive. Once the display is loose, insert a spudger between the silver frame and display assembly. Then, lift the screen out of the frame. Make sure to use a spudger instead of flat tools, as they may scratch the front panel. It is also important to use the spudger to remove the screen from the silver frame.
Disconnect Copper Contact from iPhone 4s Screen
To disassemble your iPhone, remove the protective film on the screen. Remove the screws holding the screen in place, and use a spudger to disconnect the cables from the logic board. There are seven cables on the logic board, with one of them hidden beneath the bottom cable. This cable is connected to the rear-facing camera. Using a laboratory spatula, tighten the screw. The LCD and touchscreen should now work.
